Hunter Products — Wholesale Distributor | ML Irrigation

ML Irrigation / Manufacturers / Hunter

Hunter cover control valves and controllers, and through Senninger they carry the pressure regulator range most growers end up specifying — from the ½" MPR at half a gallon a minute up to the 2" PRU at 100 gpm. The PGV and ICV valves are available with DC latching solenoids as well as 24 VAC, so the same body works on a battery controller.

51 products · 11 categories · wholesale · ships nationwide

Every Senninger regulator needs inlet pressure at least 5 psi above the preset outlet. Undersize that and the regulator simply passes whatever it is given.

Request a quote

Plastic impact sprinkler 8

Senninger 20 Series

Plastic impact sprinkler

Flow: 0.84–7.13 gpm
Pressure: 25–50 psi
Connection: 1/2" NPT male (female available)
Trajectory: 9°, 14° or 23° (models 2009 / 2014 / 2023)
Best for: Senninger’s most economical impact — risers or under-tree. Colour-coded nozzles, built-in hex wrench

Senninger Compact Impact

Plastic impact sprinkler

Flow: 3.08–7.13 gpm
Pressure: 30–50 psi
Connection: 3/4" NPT male
Trajectory: 23°
Best for: Splasharm diffuser splits the stream to bring flow closer in for better close-range coverage

Senninger WedgeDrive

Plastic impact sprinkler

Flow: 0.84–3.98 gpm
Pressure: 25–50 psi
Connection: 1/2" NPT male
Trajectory: 14° or 23° (9° also available)
Best for: Low flows and low pressures; wedge drive resists grit wear

Senninger 30 Series

Plastic impact sprinkler

Flow: 1.84–6.42 gpm
Pressure: 30–50 psi
Connection: 3/4" NPT male (female available)
Trajectory: 12° (under-tree) or 23°
Best for: Mid-range solid set and under-tree irrigation

Senninger 40 Series

Plastic impact sprinkler

Flow: 3.82–12.6 gpm
Pressure: 30–60 psi
Connection: 3/4" NPT male (female available)
Best for: Higher flows over larger spacings on solid set

Senninger 50 Series

Plastic impact sprinkler

Flow: 6.5–20.1 gpm
Pressure: 30–65 psi
Connection: 3/4" NPT male
Best for: High-flow solid set where wide spacing is needed

Senninger Part-Circle

Plastic impact sprinkler

Pressure: 30–55 psi
Connection: 3/4" NPT male
Trajectory: 23°
Radius: 38–42 ft at 1.5 ft height
Best for: Field edges, headlands and boundaries where a full circle would overthrow

Senninger 70 Series

Plastic impact sprinkler

Flow: 8.66–39.1 gpm
Pressure: 40–70 psi
Connection: 1" NPT male (1" BSPT available)
Best for: Highest flows over large diameters — Senninger states it outlasts and costs less than brass

Wobbler 3

Senninger mini-Wobbler (Upright)

Wobbler

Flow: 0.42–2.18 gpm
Pressure: 15–25 psi
Connection: 1/2" NPT male
Trajectory: 10° multi-level throw
Throw diameter: 26.5–38.5 ft at 1.5 ft height · 31–43 ft at 3 ft height
Best for: Extremely uniform coverage over a large diameter at low pressure. Mounts on a riser adapter or 26" riser stake; colour-coded nozzles warranted to hold orifice size five years

Senninger mini-Wobbler (Inverted)

Wobbler

Flow: 0.75–2.18 gpm
Pressure: 20–25 psi
Connection: 1/2" NPT male
Trajectory: 0° multi-level throw
Throw diameter: 30–32 ft at 3 ft height · 32–36 ft at 6 ft height
Best for: Inverted mount on drop adapter assemblies — overhead irrigation in greenhouse and nursery

Senninger Xcel-Wobbler

Wobbler

Flow: 0.78–6.97 gpm
Pressure: 10–25 psi
Connection: 1/2" & 3/4" NPT male
Throw diameter: Mid angle 32–44 ft · High angle 36.5–53.5 ft (at 1.5 ft height)
Best for: Wider flow range and lower minimum pressure than the mini-Wobbler; mid and high angle versions to maintain infiltration on overhead systems

Mister & fogger 3

Senninger Fogger

Mister & fogger

Flow: 6.8–23.4 gph
Pressure: 30–50 psi
Best for: Propagation and low-volume misting; consistent start-up with highly uniform distribution for short-cycle work

Senninger Mister (Upright)

Mister & fogger

Flow: 7.5–23.4 gph
Pressure: 30–50 psi
Best for: Propagation benches and humidity control; colour-coded nozzles

Senninger Mister (Inverted)

Mister & fogger

Flow: 7.5–23.4 gph
Pressure: 30–50 psi
Best for: Overhead propagation and misting from drop assemblies

Micro-sprinkler 2

Senninger Micro-Sprinkler (Upright)

Micro-sprinkler

Flow: 7.2–36.6 gph (by nozzle and pressure)
Throw diameter: 18–29 ft at 1.5–3 ft height
Best for: Container and bench irrigation; 80–140 mesh filtration by nozzle size. 14" or 26" length models

Senninger Micro-Sprinkler (Inverted)

Micro-sprinkler

Best for: Overhead irrigation in greenhouse and nursery from drop assemblies

Hanging basket assembly 1

Senninger Drop Adapter Assemblies

Hanging basket assembly

Best for: Mounts the inverted mini-Wobbler, Mister or Micro-Sprinkler on an overhead drop for hanging baskets and bench work

Pressure regulator 11

Accu-Sync

Pressure regulator

Pressure: Regulates 20–100 psi (1.4–7.0 bar)
Sizes: AS-ADJ adjustable 20–100 psi; AS-30, AS-40, AS-50, AS-70 fixed
Best for: Screws onto any Hunter control valve to hold the zone at its optimal pressure — saves water and extends the life of everything downstream. The adjustable model sets anywhere from 20 to 100 psi; the fixed models take the guesswork out. Glass-filled nylon construction. Works with both AC and DC latching solenoids

Senninger MPR (Mini Pressure Regulator)

Pressure regulator

Flow: 0.5–3.5 gpm (114–804 l/hr) by model
Pressure: Preset outlet 15, 20, 30 or 40 psi; max inlet 45–80 psi rising with the preset
Sizes: 1/2" male NPT inlet x 1/2" female NPT outlet
Best for: The smallest regulator in the line, for single heads and short runs. A greater hydraulic area than most flow-control devices lets it regulate over a wider flow range than its size suggests. Cuts wind drift and overwatering across changing elevations and long laterals, and steadies flow so every sprinkler throws its designed pattern. Models MPR152M2F through MPR402M2F. As with every Senninger regulator, inlet pressure must sit at least 5 psi above the preset outlet

Senninger PRLG (Landscape Grade)

Pressure regulator

Flow: 0.5–7 gpm (114–1590 l/hr)
Pressure: Preset outlet 10, 15, 20, 25, 30, 35 or 40 psi; max inlet 90–120 psi rising with the preset
Sizes: 3/4" female NPT inlet x 3/4" male NPT outlet (3/4" hose x hose also available)
Best for: Landscape-grade low-flow regulator, models PRLG103F3M through PRLG403F3M. Male outlet thread makes it easy to screw straight onto a valve or riser

Senninger PRL (Low Flow)

Pressure regulator

Flow: 0.5–8 gpm (114–1817 l/hr); 0.5–5 gpm on the 6 psi model
Pressure: Preset outlet 6, 10, 12, 15, 20, 25, 30, 35 or 40 psi; max inlet 80–120 psi rising with the preset
Sizes: 3/4" female NPT inlet x 3/4" female NPT outlet (3/4" hose also available)
Best for: The workhorse for solid-set, drip and other low-volume systems, and the widest preset choice at this flow — nine settings from 6 psi up. Models PRL063F3F through PRL403F3F

Senninger PSR2 (Pivot Special Regulator)

Pressure regulator

Flow: 0.5–15 gpm (114–3407 l/hr)
Pressure: Preset outlet 6, 10, 12, 15, 20, 25, 30, 35, 40 or 50 psi; max inlet 80–130 psi rising with the preset
Sizes: 3/4" female NPT inlet x 3/4" female NPT outlet
Best for: Patented design built for systems running surface water, where grit destroys ordinary regulators. Covers a much wider flow band than the PRL at the same 3/4" size. Models PSR2063F3F through PSR2503F3F

Senninger Filter Regulator

Pressure regulator

Flow: 0.5–15 gpm (114–3407 l/hr)
Pressure: Preset outlet 6–20 psi (0.41–1.38 bar)
Best for: Filtration and pressure regulation in one body, so a zone needs one fitting instead of two. Combines PSR2 performance with reduced nozzle clogging — worth it where the water carries debris and the heads are small enough to block

Senninger PMR-MF (Pressure-Master Medium Flow)

Pressure regulator

Flow: 2–20 gpm (454–4542 l/hr); 4–16 gpm on the 6 and 10 psi models
Pressure: Preset outlet 6, 10, 12, 15, 20, 25, 30, 35, 40, 50 or 60 psi; max inlet 80–140 psi rising with the preset
Sizes: 3/4" female NPT inlet x 3/4" female NPT outlet with vane
Best for: Mid-range flows for solid-set, drip and low to medium volume systems — eleven presets, the widest choice in the line, and it reaches 60 psi. Models PMR06MF3F3FV through PMR60MF3F3FV

Senninger PR-HF (High Flow)

Pressure regulator

Flow: 10–32 gpm (2271–7268 l/hr)
Pressure: Preset outlet 10, 15, 20, 25, 30, 40 or 50 psi; max inlet 90–130 psi rising with the preset
Sizes: 1 1/4" female NPT inlet x 1" female NPT outlet
Best for: Higher flows in solid-set, drip and low-volume systems. Can be installed above or below ground. Models PR10HF5F4FV through PR50HF5F4FV

Senninger PRU (Pressure Regulator Ultra)

Pressure regulator

Flow: 20–100 gpm (4542–22713 l/hr)
Pressure: Preset outlet 10, 15, 20, 25, 30, 40, 50 or 60 psi; max inlet 90–140 psi rising with the preset
Sizes: 2" female NPT inlet x 2" female NPT outlet
Best for: The largest inline regulator Senninger makes — 100 gpm through a 2" body, for a whole block or a submain rather than a single zone. Models PRU108F8F through PRU608F8F

Senninger PRLV (Pressure Regulating Limit Valve)

Pressure regulator

Flow: Up to 18 gpm (up to 4088 l/hr)
Pressure: Preset outlet 10, 15, 20, 30, 40, 50 or 60 psi; max inlet 125 psi on every model
Sizes: 3/4" female NPT inlet x 3/4" female NPT outlet with vane
Best for: Regulates and limits — it holds the preset outlet pressure and caps flow, so a burst lateral or an open end does not drain the block. Flat 125 psi max inlet across all seven presets. Models PRLV10MF3F3FV through PRLV60MF3F3FV

Senninger PRXF-LV (Extended Flow Limit Valve)

Pressure regulator

Flow: Up to 75 gpm (up to 17034 l/hr)
Pressure: Preset outlet 20, 30, 40 or 50 psi; max inlet 125 psi
Sizes: 3" female slip inlet x 3" female slip outlet
Best for: The PRLV idea at submain scale — regulation plus flow limiting up to 75 gpm through a 3" slip body that solvent-welds straight into PVC. As a limit valve it caps downstream pressure at no more than 15 psi above the regulated setting under static (no-flow) conditions, so the line does not creep up to full inlet pressure when the zone shuts. Models PRXF20LV3FS3FS through PRXF50LV3FS3FS

AC solenoid valve 4

PGV Series

AC solenoid valve

Flow: 0.2–40 gpm (0.7–150 l/min) on the 1"
Pressure: Temperature rating 150°F (66°C)
Sizes: 1" (PGV-100G globe, PGV-100A angle, PGV-101), 1½" (PGV-151), 2" (PGV-201)
Best for: Heavy-duty workhorse valve with a rugged supported diaphragm that resists stress failure and a double-beaded diaphragm seal for leak-free performance. Encapsulated 24 VAC solenoid with a captive plunger. Low-flow capability means it will run micro-irrigation zones, not just sprinkler zones. Optional DC latching solenoids for battery-powered controllers. Wide range of configurations, with or without flow control

PGV Jar-Top

AC solenoid valve

Sizes: 1" (PGV-100JT)
Best for: Same valve as the PGV but with a glass-filled nylon threaded jar ring — service it without tools. The fastest option when valves get opened often for cleaning. Encapsulated 24 VAC solenoid; optional DC latching solenoid

ICV Series

AC solenoid valve

Pressure: Operates continuously to 220 psi
Sizes: 1½", 2", 3" (ICV-301G)
Best for: Hunter’s commercial-grade valve for larger mainlines and higher flows, with captive bonnet bolts for hassle-free maintenance. Encapsulated 24 VAC solenoid; optional DC latching solenoid. Pairs with Accu-Sync for pressure regulation

Drip Control Zone Kits

AC solenoid valve

Connection: Valve, filter and pressure regulator preassembled
Best for: A complete drip zone in one part — control valve, 150-mesh filter and regulator already put together and tested. Cuts the head assembly from a bench job to a single connection

DC latching solenoid valve 2

PGV Series (DC latching)

DC latching solenoid valve

Flow: 0.2–40 gpm (0.7–150 l/min) on the 1"
Pressure: Temperature rating 150°F (66°C)
Sizes: 1" (PGV-100G globe, PGV-100A angle, PGV-101), 1½" (PGV-151), 2" (PGV-201)
Best for: The standard PGV ordered with a DC latching solenoid instead of the 24 VAC one, so it runs from a Hunter battery-powered controller. Rugged supported diaphragm with a double-beaded seal; low-flow capability means it will drive micro-irrigation zones, not just sprinklers. Pairs with Accu-Sync for pressure regulation

ICV Series (DC latching)

DC latching solenoid valve

Pressure: Operates continuously to 220 psi
Sizes: 1½", 2", 3" (ICV-301G)
Best for: Hunter’s commercial valve ordered with a DC latching solenoid for battery-powered control on larger mainlines. Captive bonnet bolts for hassle-free maintenance

AC Controller 13

ACC2

AC Controller

Connection: Up to 6 flow meter inputs and 6 pump / master valve outputs
Sizes: 12 to 54 stations
Best for: Hunter’s top commercial controller, for a site big enough to need real flow management — multiple flow meters and multiple pump or master valve outputs on one controller. Also available as an ACC2 Decoder for two-wire

Pro-C

AC Controller

Connection: Conventional wiring, EZ Decoder two-wire, or hybrid conventional/two-wire
Best for: The practical middle of Hunter’s range and the one they name for nurseries. Expandable, and you can wire it conventionally, run EZ Decoder two-wire, or mix both on the same controller — useful when an old block is being extended

I-Core

AC Controller

Best for: Commercial controller sitting between the Pro-C and the ACC2, with conventional or decoder operation

X-Core

AC Controller

Sizes: Up to 8 stations; 3 programs with 4 start times each
Best for: Small, straightforward controller for a compact block or a single house

ICC2

AC Controller

Connection: Any combination of conventional, EZDS two-wire and Wireless Valve Link outputs on one controller; built-in flow monitoring
Best for: The most flexible wiring of any Hunter controller — conventional stations, two-wire decoders and wireless valve links all at once. That means an old block, a new extension and an unreachable corner can share one controller instead of three. Built-in flow monitoring, and online control through Centralus

HPC

AC Controller

Best for: The Pro-C cabinet with Hydrawise Wi-Fi control built in — modular and expandable, managed from the app

HCC

AC Controller

Best for: Hunter’s commercial controller running Hydrawise — Wi-Fi scheduling and monitoring at commercial station counts

Pro-HC

AC Controller

Best for: Pro-C hardware with Hydrawise Wi-Fi — one of the three replacements for the discontinued HC

X2 with WAND

AC Controller

Connection: WAND module adds Hydrawise Wi-Fi to a dial controller
Best for: You do not have to choose between Wi-Fi and a dial. The X2 runs perfectly well from the face plate, and the WAND module adds Hydrawise later if the site wants app control — useful where a grower is not ready to put irrigation on the network

MCC

AC Controller

Best for: Hunter’s modular commercial controller platform

Centralus Irrigation Management

AC Controller

Connection: Adds cloud control and monitoring to ACC2, ICC2 and Pro-C
Best for: Puts existing ACC2, ICC2 and Pro-C controllers under cloud control and monitoring from a mobile-friendly platform — no controller replacement needed

EZ Decoder System (EZDS)

AC Controller

Best for: Converts a Pro-C, HPC or ICC2 to two-wire — one cable out to the field with decoders dropped where valves are needed, instead of a home run per station

Wireless Valve Link

AC Controller

Best for: Runs a valve with no wire to it at all — for a zone across a road or beyond an obstacle where trenching is not worth it. Works alongside conventional and two-wire on the ICC2

DC Controller 2

NODE

DC Controller

Connection: Mounts straight onto a valve solenoid — no screws, drills or extra wires
Best for: Waterproof battery controller for temporary irrigation and anywhere without power. It clips onto the valve itself, so a single remote zone can be automated without running anything back to a panel

NODE-BT

DC Controller

Connection: Bluetooth; mounts on the valve solenoid
Best for: The NODE with Bluetooth — programmed from a phone at the valve rather than through the face buttons. For remote zones with no power and no wiring

Filtration 2

HY Series Filters

Filtration

Flow: Up to 20 gpm
Pressure: 20–120 psi; 150-mesh stainless steel screen (120-mesh nylon also available)
Sizes: HY-075 (¾"), HY-100 (1"), HY-151 (1½")
Best for: The filter that belongs in front of every drip and micro zone. Stainless 150-mesh screen, and the ¾" and 1" sizes cover most nursery heads

HFR Filter Regulators

Filtration

Flow: 0.5 to 15 gpm
Pressure: Regulates to 25 or 40 psi; 150-mesh stainless steel screen
Connection: Preassembled with flush cap
Sizes: HFR-075-25 and HFR-075-40 (¾"), HFR-100-075-25 and HFR-100-075-40 (1" inlet x ¾" outlet)
Best for: Filter and regulator preassembled in one unit with a flush cap — one fitting instead of three at the head of a drip zone, and nothing to mis-assemble. Choose 25 or 40 psi at order

Hunter by category

Plastic impact sprinkler·Wobbler·Mister & fogger·Micro-sprinkler·Hanging basket assembly·Pressure regulator·AC solenoid valve·DC latching solenoid valve·AC Controller·DC Controller·Filtration