PolyRail 16mm Aluminum Extrusion
Bench & tubing support- Sizes
- Item ALU16 · Sizes 12' section
- Best for
- PolyRail aluminum extrusion tightly sleeves PE tubing keeping it rigid, without sags. PolyRail keeps nozzles straight and even, ensuring the best coverage for your irrigation system. Installs easily without glue.
Catalog ↗PolyRail 25mm Aluminum Extrusion
Bench & tubing support- Sizes
- Item ALU25 · Sizes 12' section
- Best for
- 25mm (3/4) diameter. For higher flow and more support. 25mm PolyRail may be used to hang baskets
Catalog ↗PolyRail Connecting Band
Bench & tubing support- Sizes
- Item ALU501CB · Sizes 4 inch
- Best for
- Connecting band with set screws. 4 length. Connects two rail pieces together.
Catalog ↗PolyRail 90 deg Hanger 16mm
Bench & tubing support- Sizes
- Item ALU500PH · Sizes 16mm
- Best for
- Right-angle hanger that carries 16 mm PE tubing off the PolyRail extrusion. Item ALU500PH — the 25 mm hanger is ALU500-90.
Catalog ↗PolyRail 90 deg Hanger 25mm
Bench & tubing support- Sizes
- Item ALU500-90 · Sizes 25mm
- Best for
- Right-angle hanger for 25 mm PE tubing on the PolyRail extrusion. Item ALU500-90 — the 16 mm hanger is ALU500PH.
Catalog ↗PolyRail Top Hanger
Bench & tubing support- Sizes
- Item ALU502H · Sizes Top
- Best for
- Hanger rides on Rail to position PE outlet towards the bottom of the Rail.
Catalog ↗PolyRail Stop
Bench & tubing support- Sizes
- Item ALU541S · Sizes -
- Best for
- Stop used at both ends of each irrigation run. Includes set screw.
Catalog ↗PolyRail Punch 25mm
Bench & tubing support- Sizes
- Item ALU503A · Sizes 25mm
- Best for
- Punch sized for 25 mm PolyRail tubing. Item ALU503A — use ALU509A on 16 mm.
Catalog ↗PolyRail Punch 16mm
Bench & tubing support- Sizes
- Item ALU509A · Sizes 16mm
- Best for
- Punch sized for 16 mm PolyRail tubing, so the hole matches the fitting instead of being stretched to suit. Item ALU509A — use ALU503A on 25 mm.
Catalog ↗PolyRail Bench Riser Base
Bench & tubing support- Sizes
- Item ALUSB · Sizes -
- Best for
- Base for PolyRail Bench Riser Support
Catalog ↗PolyRail Bench Riser Cap
Bench & tubing support- Sizes
- Item ALUSC · Sizes -
- Best for
- Cap for top of PolyRail Bench Riser Support
Catalog ↗No-Drip Riser
Bench & tubing support- Sizes
- Item NDR · Sizes - · Colors -
- Best for
- Riser with a no-drip mechanism that shuts as pressure falls, so the nozzle does not dribble onto the crop after the cycle ends. Item NDR.
Catalog ↗No-Drip Extension with Check Valve
Bench & tubing support- Sizes
- Item NDECV · Sizes - · Colors -
- Best for
- No-drip riser extension with a check valve fitted — adds height and stops backflow down the riser. Item NDECV. Use the plain NDR riser where no extension is needed.
Catalog ↗Run-Out Valve
Bench & tubing support- Sizes
- Item ROV · Sizes - · Colors -
- Best for
- Run-Out Valves are designed to be installed at the end of 1-inch or 3/4-inch PVC pipelines. When the water is turned off, the Run-Out Valve will open and allow water to run out of the line, eliminating drip from all overhead nozzles. Run-Out Valves require at least 15 PSI to work properly. Use PVC cement and a 1 to 3/4 PVC reducer bushing to connect Run-Out Valves to 3/4-inch PVC pipelines. Follow the PVC cement directions regarding pipe preparation and drying times.
Catalog ↗Threaded Pipe Nipple
Bench & tubing support- Sizes
- Item PN-2010 · Sizes - · Colors -
- Best for
- The Threaded Pipe Nipple is used to attach Dramm Irrigation Nozzles directly to 1/2 PVC pipe risers. To install, simply screw the Threaded Pipe Nipple onto the threaded 1/2 PVC pipe riser. This method is ideal when you want to eliminate overhead lines or when overhead lines are impossible. 1/2 NPT X 3/8 WW . Use with 1/2 threaded PVC risers.
Catalog ↗Slip Fit Pipe Nipple
Bench & tubing support- Sizes
- Item PN-2020 · Sizes - · Colors -
- Best for
- The Slip Fit Pipe Nipple is used to attach Dramm Irrigation Nozzles directly to straight (unthreaded) 1/2 PVC pipe risers. To install, use PVC cement to attach the Slip Fit Pipe Nipple onto PVC pipe risers. Follow the PVC cement directions regarding pipe preparation and drying times. This method is ideal when you want to eliminate overhead lines or when overhead lines are impossible. 1/2 NPT X 3/8 WW . Use with 1/2 straight PVC risers.
Catalog ↗Drill Tap 3/8 Whitworth Thread
Bench & tubing support- Sizes
- Item DT-N · Sizes - · Colors -
- Best for
- Creates a 3/8 Whitworth thread in PVC for Pin-Perfect, Nifty or Misty Mist Nozzles.
Catalog ↗3/4 Kwik Klamp
Bench & tubing support- Sizes
- Item KK-75 · Sizes 3/4 in · Colors -
- Best for
- The Kwik Klamp is a bracket with a hinged clip that can open and close. This handy device locks shut when closed, but can be opened to remove or replace pipelines. The Kwik Klamp makes pipe installation fast and easy. Made in the Netherlands from chemical resistant polypropylene. Available for 3/4 and 1 diameter pipes. Metric and additional inch sizes are available upon special order. Use with the Kwik Spacer.
Catalog ↗1 Kwik Klamp
Bench & tubing support- Sizes
- Item KK-100, KK-125, KK-150, KK-200 · Sizes 1 in, 1.25 in, 1.5 in, 2 in · Colors -
Catalog ↗3/4 Kwik Spacer
Bench & tubing support- Sizes
- Item KS-75 · Sizes 3/4 in · Colors -
- Best for
- The Kwik Spacer slides into the Kwik Klamp and is used to create additional space between the pipe and wall. Multiple Kwik Spacers can be combined to create varying lengths in 3/4 increments. Made in the Netherlands from chemical resistant polypropylene. Available for 3/4 and 1 Kwik Klamps. Metric and additional inch sizes are available upon special order.
Catalog ↗1 Kwik Spacer
Bench & tubing support- Sizes
- Item KS-100, KS-125, KS-150, KS-200 · Sizes 1 in, 1.25 in, 1.5 in, 2 in · Colors -
Catalog ↗On Dribble Tube
Bench & tubing support- Sizes
- Item DTS-18, DTS-24, DTS-30, DTS-36, DTS-42, DTS-48, DTS-60, DTM-12, DTM-18, DTM-24, DTM-30, DTM-36 (+11 more) · Sizes 18 in, 24 in, 30 in, 36 in, 42 in, 48 in, 60 in, 12 in · Colors Green Tubing, Brown Tubing, Blue Tubing
Catalog ↗Dramm Stix
Bench & tubing support- Sizes
- Item SS-16, SS-24, SS-30, SS-36 · Sizes 16 in, 24 in, 30 in, 36 in · Colors -
Catalog ↗Brass Eyelet
Bench & tubing support- Sizes
- Item DTMS-E · Sizes .060 or .045 ID · Colors -
- Best for
- Brass eyelet. Used to install Dramm Dribble Tubes and Dribble Rings.
Catalog ↗Valve Station
Bench & tubing support- Sizes
- Item Valve Station · Sizes - · Colors -
- Best for
- Dramm offers preassembled valve stations as well as multi line manifolds. Build with easy maintenance in mind, Dramm pre assembled PVC components make irrigation system installation easy. Talk to Dramm about designing your irrigation system today and include Dramm pre assembled system components.
Catalog ↗Abot/Riser Base 1.5
Bench & tubing support- Sizes
- Item A-050-001-607 · Sizes 1.5 in · Colors -
- Best for
- The Abot Riser base connects laterals to risers.
Catalog ↗Male End Fitting 1.5
Bench & tubing support- Sizes
- Item A-050-001-616 · Sizes 1.5 in · Colors -
Catalog ↗Female End Fitting 1.5
Bench & tubing support- Sizes
- Item A-050-001-517 · Sizes 1.5 in · Colors -
Catalog ↗Riser Pipe (Black) ED x20inch
Bench & tubing support- Sizes
- Item A-032-032-450 · Sizes - · Colors -
- Best for
- 20 inch riser section for PipeLoc. Threads into Riser Base and connects to other riser pipes to reach desired nozzle height.
Catalog ↗Abot/Riser Base 2
Bench & tubing support- Sizes
- Item A-063-001-607, A-075-001-607, A-090-001-607, A-050-050-621, A-063-063-623, A-075-050-624, A-075-063-625, A-075-075-626, A-090-050-627, A-090-063-628, A-090-075-629, A-090-090-630 (+43 more) · Sizes 2 in, 2.5 in, 3 in, 1.5 in, 2.5 in/1.5 in, 2.5 in/2 in, 3 in/1.5in, 3in/2in, 3in/2.5in, 3 in/2 in (+3 more) · Colors -
Catalog ↗