Rivulis Products — Wholesale Distributor | ML Irrigation

ML Irrigation / Manufacturers / Rivulis

Rivulis cover the same ground as Netafim and are often the better commercial answer on a given block — T-Tape and Ro-Drip for seasonal row work, the D-series dripline range for permanent plantings, and a filtration line that goes from simple screens to automatic self-cleaning units. Since the 2022 merger with Jain's international business the NaanDan and AmnonDrip products sit under the same roof.

77 products · 18 categories · wholesale · ships nationwide

Rivulis publish more sprinkler and dripline models than any distributor stocks. Tell us the block and we will tell you which of them is actually worth ordering.

Request a quote

Drip tape 2

T-Tape

Drip tape

Diameter: 16–35 mm (5/8"–1-3/8")
Wall: 4–15 mil
Emitter spacing: 4"–30"
Flow: ~0.066–1.06 gph (0.25–4.0 l/h)
Pressure: ~8 psi nominal
Pressure comp.: No · PC dripline alternative: D4000 PC
Best for: Open-field vegetables & row crops; heavier walls for multi-season/SDI

Ro-Drip

Drip tape

Diameter: 5/8" (7/8" also)
Wall: 8–15 mil (approx.)
Emitter spacing: 4" (others offered)
Flow: varies (~0.40 gpm/100 ft class)
Pressure: ~8 psi nominal
Pressure comp.: No · PC dripline alternative: D4000 PC
Best for: New-to-drip growers or very poor water (expanding-labyrinth anti-clog)

Dripline 8

D900

Dripline

Diameter: 16 & 22 mm
Wall: 5–12 mil
Emitter spacing: 10–75 cm (4"–30")
Flow: 0.17, 0.26, 0.37 & 0.58 gph (0.65, 1.0, 1.4, 2.2 l/h)
Pressure: 17 psi max (1.2 bar)
Pressure comp.: No · PC version: D4000 PC
Coil lengths: up to 2,600 m (8,530')
Best for: Single-season crops; engineered for longer run lengths at high uniformity (fewer tractor turns)

D1000

Dripline

Diameter: 16 & 22 mm
Wall: 6, 8, 10 & 12 mil
Emitter spacing: 15–50 cm (6"–20")
Flow: 0.17, 0.26 & 0.40 gph (0.64, 1.0, 1.5 l/h)
Pressure: 14.5–17 psi max (1.0–1.2 bar)
Pressure comp.: No · PC version: D4000 PC
Coil lengths: 2,300–3,000 m
Best for: Shallow-burial / subsurface, single-season

D2000

Dripline

Diameter: 16 & 17 mm
Wall: 18, 30, 35, 40 & 45 mil
Emitter spacing: 20–100 cm (8"–39")
Flow: 0.40, 0.52 & 0.53 gph (1.5, 1.95, 2.0 l/h)
Pressure: 32–43.5 psi max (2.2–3.0 bar)
Pressure comp.: No · PC version: D5000 PC
Coil lengths: 400–1,100 m
Best for: Medium-heavy-wall runs needing high clog resistance

D4000 PC

Dripline

Diameter: 16 & 22 mm
Wall: 8 & 10 mil
Emitter spacing: 12" (example)
Flow: 0.16 & 0.24 gph (0.6, 0.9 l/h)
Pressure: 4.4–21.8 psi (0.3–1.5 bar)
Pressure comp.: Yes · Non-PC version: D1000 or Eolos Classic
Coil lengths: 1,000–2,000 m
Best for: Annual crops on slopes to ~2%; long runs

D5000 PC

Dripline

Diameter: 16, 17, 20, 22 & 23 mm
Wall: 13, 15, 35 & 40 mil
Emitter spacing: 15–100 cm (6"–39")
Flow: 5 flow rates to 0.69 gph (2.6 l/h)
Pressure: 26–43.5 psi max (1.8–3.0 bar)
Pressure comp.: Yes · Non-PC version: D2000 or Eolos Classic
Coil lengths: 350–800 m
Best for: Subsurface (SDI), hilly terrain, long runs, orchards

Hydro PC / PCND

Dripline

Diameter: 16, 17 & 20 mm
Wall: 35, 45 & 47 mil
Emitter spacing: 8", 12", 16", 20", 24", 30" & 36"
Flow: 0.42 & 0.46 gph
Pressure: 44–51 psi max; PC regulates from 14.5 psi (16 mm) / 10.6 psi (17 mm and above)
Pressure comp.: Yes · Non-PC version: Eolos Classic
Coil lengths: 1,000'
Best for: Orchards, vineyards, greenhouses; PCND enables pulse irrigation

Eolos Classic

Dripline

Diameter: 16 mm
Wall: 5–35 mil
Emitter spacing: 15–75 cm (6"–30")
Flow: up to 1.06 gph (4.0 l/h)
Pressure comp.: No · PC version: D4000 PC or D5000 PC
Best for: Single- to multi-season crops; wall-thickness durability tiers

AmnonDrip PC / CNL / AS (NaanDanJain)

Dripline

Diameter: 16, 17, 20 & 23 mm
Wall: 25, 35, 40 & 45 mil
Emitter spacing: 20–100 cm
Flow: ~0.29–1.00 gph (1.1–3.8 l/h)
Pressure: 36–51 psi max (2.5–3.5 bar)
Pressure comp.: Yes · Non-PC version: Eolos Classic
Best for: Long laterals / variable terrain; greenhouse, vegetables, orchards; SDI (AS)

Oval hose 1

Rivulis Oval Hose

Oval hose

Diameter: 0.660"–2.743" ID
Wall: .026"–.108"
Pressure: 21 & 42 psi grades
Coil lengths: 250'–3,000'
Sizes: 1/2", 3/4", 1", 1-1/4", 1-1/2" & 2"
Best for: Submain and water transfer; premium PE resin, lays flat for freight and storage

Layflat 4

H5000 Layflat

Layflat

Diameter: 41, 50, 65, 75, 100, 125, 150 & 200 mm (1-1/4"–8")
Wall: 1.15–2.20 mm
Pressure: 42–71 psi (2.9–4.9 bar)
Coil lengths: 100 m rolls
Best for: PVC layflat submain — H5100 (blue) standard pressure, H5200 (red) high pressure

Pro-Flat Layflat

Layflat

Diameter: 1.5", 2", 3", 4", 6" & 8"
Wall: .059"–.090"
Pressure: 45–91 psi max operating (by size)
Coil lengths: 300'
Best for: Heavy-duty layflat with embedded webbing and strong yarn structure; USA & Mexico

H6000 PE Layflat

Layflat

Diameter: 75 mm (3"), 100 mm (4") & 150 mm (6")
Wall: 0.95 mm (37.4 mil)
Emitter spacing: Outlet spacing 0.50–2.00 m (19.7"–78.7"); custom spacing available
Pressure: 3" 33 psi plain / 26 psi with outlets · 4" 29 / 22 psi · 6" 20 / 14.5 psi
Coil lengths: 100 m (328 ft) rolls
Best for: Outlets injection-moulded into the layflat — no punching, no leaks at the outlet. Up to 64% lighter than equivalent PVC layflat. Connects to seamless thinwall laterals up to 25 mil wall

H6500 PE Layflat

Layflat

Diameter: 75 mm (3") & 100 mm (4")
Wall: 1.2 mm (47.2 mil) on 3"; 1.42 mm (51.2 mil) on 4"
Emitter spacing: Outlet spacing 0.508–1.524 m (20"–60"); custom spacing available
Pressure: 3" 33 psi plain / 26 psi with outlets · 4" 29 / 22 psi
Coil lengths: 100 m (328 ft) rolls
Best for: As H6000 but seamless construction and works with standard fittings. Up to 60% lighter than equivalent PVC layflat. Connects to seamless thinwall laterals up to 25 mil wall

Plastic impact sprinkler 9

5035 SD

Plastic impact sprinkler

Flow: 3.10–12.71 gpm
Pressure: 35–70 psi
Connection: 3/4" male
Throw diameter: 80–111 ft
Sizes: Single nozzle or dual nozzle; #18 (9/64", 3.5 mm) and larger, colour-coded bayonet
Best for: General field use on solid-set systems. Unique hammer with the SD super-diffuser plate holds uniform distribution on single or dual nozzles at spacings up to 65 ft, and the impact drive handles wind. Colour-coded bayonet nozzle with an integrated stream-straightening vane for maximum range. Full and part circle; a PC version is also listed. Heavy-duty plastic resists corrosion, chemicals and UV

5022 SD

Plastic impact sprinkler

Flow: 1.46–5.28 gpm
Pressure: 25–60 psi
Connection: 1/2" sprinkler carrier adaptor for Stand 52/53
Throw diameter: 63–85 ft
Sizes: Single or dual nozzle — #12 (3/32"), #14, #15 and up, colour-coded bayonet
Best for: Irrigation and germination of vegetables, flowers and nursery crops. Hammer plus SD super-diffuser plate gives uniform distribution across a wide spacing range, including good coverage on field boundaries. Reduced clogging sensitivity and high wind resistance; short-cycle friendly for germination. Full and part circle

5024 SD

Plastic impact sprinkler

Flow: 1.38–4.30 gpm
Pressure: 22–60 psi
Trajectory: 12° low angle
Throw diameter: 49–75 ft
Sizes: #12 (3/32", 2.5 mm) and up, colour-coded bayonet
Best for: Undertree irrigation in orchards and plantations — table grapes and bananas especially. The 12° low-angle body keeps the stream under the canopy, and it holds uniformity down to 22 psi. Optional anti-theft adaptor. UV and impact resistant

5030LT

Plastic impact sprinkler

Flow: 3.7–8.7 gpm (831–1981 l/h)
Pressure: 29–58 psi (2–4 bar)
Connection: 3/4" male threaded inlet
Trajectory: 25°
Throw diameter: 80–97 ft (24.5–29.5 m)
Sizes: Single or dual nozzle — 4.0 mm black, 3.5 mm blue and others
Best for: Cost-focused field sprinkler for pulses, oilseeds, vegetables and cereals, with the Super Diffuser plate for distribution. Springs protected with a cap and ring; heavy-duty spindle and fulcrum pin. Carries a specific one-year limited warranty rather than the standard Rivulis terms

501-U

Plastic impact sprinkler

Flow: 0.44–1.10 gpm (100–250 l/h)
Pressure: 22–51 psi (1.5–3.5 bar)
Connection: 1/2" male quick connector, mounted on IrriStand 50
Throw diameter: 39–51 ft (12–15.5 m)
Sizes: 1.6 mm red and 1.8 mm green nozzles
Best for: Turbo-hammer low-volume sprinkler for vegetables — leafy greens especially — and greenhouses, at spacings up to 26 ft (8 m). Fine droplets for delicate crops; corrosion-resistant metal parts and easy inspection for maintenance

6004 SD

Plastic impact sprinkler

Flow: 2.11–3.59 gpm (480–815 l/h)
Pressure: 29–58 psi (2.0–4.0 bar)
Trajectory: 4° low angle
Throw diameter: 46–59 ft (14–18 m)
Best for: Ground-level precision for orchards and plantations, aimed at table grapes and bananas. The 4° low angle throws a flat stream close to the ground so foliage stays dry, and a special arched water path maximises coverage diameter. Drive mechanism is designed to resist snail damage. UV and impact resistant

6024 SD

Plastic impact sprinkler

Flow: 1.56–3.21 gpm (355–730 l/h)
Pressure: 29–44 psi (2.0–3.0 bar)
Trajectory: 12° low angle
Throw diameter: 49–66 ft (15–20 m)
Best for: Under-canopy irrigation in orchards and plantations — table grapes and bananas. Low-angle, low-volume build with the SD super-diffuser plate and an arched water path for maximum coverage. Snail-resistant drive; colour-coded bayonet nozzles. UV resistant

6025 SD

Plastic impact sprinkler

Flow: 2.4–5.6 gpm (0.54–1.27 m³/h)
Pressure: 36–58 psi (2.5–4.0 bar)
Connection: 1/2" NPSI female x 3/4" BSPP female adaptor; 3/4" PVC riser for Elite 50 mm
Throw diameter: 62–89 ft (19–27 m)
Sizes: 2.8 mm orange, 3.0 mm red and up, colour-coded bayonet
Best for: Irrigation and germination of vegetables, field crops and flowers on short cycles. Arched water path widens the radius so fewer sprinklers cover the block — spacing 12–16 m. Reduced clogging sensitivity, high wind resistance, and full protection of the spring and axle area

427 GAG / 427B AG-U

Plastic impact sprinkler

Flow: 2.00–5.28 gpm
Pressure: 30–60 psi
Connection: 1/2" MPT, mounts on IrriStand 52
Throw diameter: 72–85 ft
Best for: Plastic impact sprinkler in heavy-duty materials resistant to corrosion, chemicals and UV

Metal impact sprinkler 4

233B / 234

Metal impact sprinkler

Flow: 3.5–20.3 gpm (0.79–4.60 m³/h)
Pressure: 44–73 psi (3.0–5.0 bar)
Pressure comp.: PC version available (233B PC)
Connection: 3/4" male / female
Radius: 45–70 ft (89–141 ft wetted diameter, 27–43 m)
Sizes: 3.5x2.5L blue, 4.0x2.5L red/black and larger dual nozzles
Best for: Heavy-duty metal overhead sprinkler for precision irrigation at spacings of 12–20 m. Available as 233B or 234, with a pressure-compensating 233B PC

423

Metal impact sprinkler

Flow: 2.53–4.13 gpm
Pressure: 30–60 psi
Connection: 1/2" MPT
Trajectory: 27°
Radius: 38–46 ft (76–92 ft wetted diameter)
Best for: Metal impact for field edges, end-of-lateral runs, nurseries and medium to large landscape areas, at spacings up to 45 ft. The WP hammer keeps water inside the pattern so roads and structures stay dry. Sand and dust protection sleeve; diffuser screw, distance control flap and wetting precision arm all fitted. Full or part circle

260

Metal impact sprinkler

Flow: 12.8–47.1 gpm (2.9–10.7 m³/h)
Pressure: 22–58 psi (1.5–4.0 bar)
Pressure comp.: PC version available (K1-260 PC)
Connection: 1 1/4" female
Radius: 51–77 ft (102–154 ft wetted diameter, 31–47 m)
Sizes: 8.0 mm, 9.0 mm and larger nozzles
Best for: K1-260 metal impact sprinkler for spacings up to 27 m

280

Metal impact sprinkler

Flow: 41.8–221.5 gpm (9.5–50.3 m³/h)
Pressure: 22–87 psi (1.5–6.0 bar)
Pressure comp.: PC version available (Duplex 280 PC)
Radius: 66–150 ft (131–305 ft wetted diameter, 40–93 m)
Sizes: 12.0x8.0, 14.0x8.0 mm and larger dual nozzles
Best for: Duplex 280 big-gun metal impact for spacings up to 50 m

Fertilizer injector 1

Automated Fertigation Injection Systems

Fertilizer injector

Best for: Accurate nutrient delivery with pH control. Rivulis range runs from basic venturi injection through to fully automated systems

Micro-sprinkler 10

Super Green Spin

Micro-sprinkler

Flow: 11.4–42.3 gph at 29 psi
Pressure: 30–45 psi
Connection: Tapered or bayonet; fits PE and PVC pipe
Throw diameter: 24.6–31.2 ft (tested 6 ft above ground)
Sizes: 5 colour-coded nozzles — brown 11.4, grey 18.5, green 27.7, orange 31.7, black 42.3 gph
Best for: Bridgeless no-drip inverted micro-sprinkler for overhead greenhouse irrigation. Sand protection plate and sand release slots resist clogging; improved bearing and swivel for wear resistance. Optional Super LPD leakage prevention device. Filtration 120 mesh on brown and grey nozzles, 70 mesh on green, orange and black

Rondo / RFR

Micro-sprinkler

Flow: Rondo 7.9–78.7 gph (30–298 l/h); RFR 6.1–25.1 gph (23–95 l/h)
Pressure: Rondo 22–36 psi (1.5–2.5 bar); RFR 22–51 psi (1.5–3.5 bar)
Pressure comp.: Yes on the RFR version · Non-PC version: Rondo
Connection: 3/8" threaded, or 5 mm thread inlet option
Throw diameter: 19–36 ft (5.8–11.0 m) at 29 psi
Best for: Rotating micro-sprinkler for field and protected crops, also run inverted. RFR is the pressure-compensating build for undulating ground and long laterals. Filtration steps with flow: 120 mesh to 40 l/h, 80 mesh 40–70 l/h, 60 mesh above 70 l/h

AquaMaster 2005

Micro-sprinkler

Flow: 8–96 gph
Pressure: 20–45 psi
Connection: 3/8" MPT, 1/2" MPT, quick thread, or 4/7 barb
Throw diameter: 18–41 ft
Sizes: 7 colour-coded nozzles, .031"–.076" — violet 9, brown 13, grey 18, green 28, orange 32, black 42, blue 53 gph nominal
Best for: Widely-spaced plantations — walnut, almond, avocado, mango — and overhead irrigation of vegetables and nursery stock. Insect-resistant nozzle and large droplets; inverted version for tunnels and greenhouses. Two-stage swivels available. Filtration 120 mesh on violet and brown nozzles, 70 mesh on the rest

AquaSmart 2002

Micro-sprinkler

Flow: 5.3–25.1 gph
Pressure: 20–60 psi
Connection: 4/7 barb, female, or 3/8" MPT quick thread
Throw diameter: 9.5–25 ft
Best for: Steady flow across a wide pressure band for orchards and vineyards on varied topography. Insect-proof nozzle, clog-resistant even at low flow. Spring-loaded inverted bridge option; two-stage swivels give wetted-diameter control — first stage limits diameter for young trees. Optional trunk protector keeps water off the trunk

Flipper

Micro-sprinkler

Flow: 6.6–11.4 gph at 29 psi
Pressure: 29–45 psi (35–55 psi for the regulated unit)
Throw diameter: Narrow strip pattern — spacing up to 18, 20 or 32 ft by nozzle, mounted 3 ft above target
Sizes: 3 nozzles — black 6.6, violet 9.3, brown 11.4 gph; flow regulators at 6.6 / 9.3 / 11.4 gph
Best for: Frost protection for vineyards and row orchards. Throws a long narrow strip down the row instead of a circle, saving up to 70% of the water a conventional overhead system uses. Large droplets minimise evaporative cooling at start-up; pathways stay dry for equipment access. 120 mesh filtration

Modular

Micro-sprinkler

Flow: 7.7–98.7 gph
Pressure: 25–45 psi
Connection: 4/7 barb, barbed butterfly, spike, or suspended stand with weight
Throw diameter: 4.9–36 ft
Best for: One frame, a full range of heads — full and part circle, with small, medium or large droplets depending on the sprayer, swivel or optional anti-mist device. Spreader available for inverted use. Filtration 120 mesh on purple and brown nozzles, 80 mesh on the rest

Hadar 7110

Micro-sprinkler

Flow: 6.1–88 gph (23–333 l/h)
Pressure: 22–44 psi (1.5–3.0 bar)
Connection: Bayonet coupling
Throw diameter: 5.6–36 ft (1.7–11.0 m) at 29 psi
Sizes: 11 colour-coded nozzles, 0.65–2.0 mm; 9 inserts — mist sprayer, small sprayer, extra-range, insect-resistant, half-circle, mini-range rotor, medium-range rotor, extra-range rotor, inverted rotor
Best for: Modular build with bayonet coupling — swap inserts to change the pattern without replacing the head. Covers irrigation, propagation and micro-climate work in orchards, greenhouses, nurseries and landscape. Can be run with a leakage prevention device

S2000 / S2000 PC

Micro-sprinkler

Flow: S2000 7.7–79.3 gph (29–300 l/h); S2000 PC 6.3–25.1 gph (24–95 l/h)
Pressure: 22–51 psi (1.5–3.5 bar)
Pressure comp.: Yes on the PC version · Non-PC version: S2000
Connection: Meteor adaptor with cantal stake, or hung from LDPE
Throw diameter: S2000 20–34 ft (6.0–10.5 m); S2000 PC 16–25 ft (5.0–7.5 m), measured 10" above ground
Best for: Take-apart body opens in one click for service. Low trajectory keeps water off the fruit; anti-insect protection standard; wear-resistant movement. PC version holds flow steady on undulating ground and long runs. Snap-off range limiter shrinks the pattern for young trees — break the tab off as they mature

Tornado Ray Jet Sprayer

Micro-sprinkler

Flow: 7.1–18.5 gph (26.7–70 l/h) at 22 psi
Pressure: 22–44 psi (1.5–3.0 bar)
Connection: PE 4x7 mm tube with cantad stake, or take-apart body
Throw diameter: 8–14 ft (2.4–4.2 m), upright 10" above ground
Sizes: 4 nozzles — black 0.9, blue 1.3, green 1.7, red 2.0 mm; 360° and 300° patterns
Best for: Fixed jet sprayer for close-in coverage; take-apart version for cleaning. Nozzles listed are for use with a pressure regulator — conic nozzles for non-PC service on request. Filtration 120 mesh to 40 l/h, 80 mesh 40–70 l/h

Smart Jet

Micro-sprinkler

Flow: 5.0–20.9 gph
Pressure: 15–40 psi
Pressure comp.: Yes — Smart Jet PC
Connection: 160 barb with 160x220" PE tube, or clip hammer stake 36"
Throw diameter: 10–28 ft depending on pattern (J 16-jet, U 270°, C 210°, A high, A low, S strip)
Sizes: 7 colour-coded nozzles, .033"–.065" — black 5.0, orange 7.4, blue 9.2, violet 12.2, green 14.5, yellow 17.7, red 20.9 gph
Best for: Uniform frame takes any of six jet patterns, so one part number covers the block. PC model holds flow steady and supports longer laterals. Optional Top Hat limits the wetted area on young trees. Strip pattern throws 2.5–4 ft wide. Filtration 120 mesh on black, orange and blue nozzles, 75 mesh on violet, green, yellow and red

Mister & fogger 5

Super Fogger

Mister & fogger

Flow: Medium pressure 1.5 / 3.0 / 5.5 gph at 40 psi; high pressure 6.5 / 13 / 24 gph at 60 psi
Pressure: Medium (green cover) 40 psi, max 45 psi; high (blue cover) 60 psi
Connection: Multi-connection for PE pipe, or 3/8" thread for PVC
Sizes: 1, 2 or 4 outlets
Best for: Greenhouse cooling, humidification and chemical application. Built-in leakage prevention device — medium-pressure model opens at 45 psi and closes at 20, high-pressure opens at 60 and closes at 35. Droplets average 2.7 mil medium / 2.1 mil high, so foliage stays dry under pulsed operation. Built-in filter. Climate control spacing 5x10 to 10x10 ft; pesticide spraying 5x10 ft; poultry 5–10 ft. 120 mesh filtration

FLF Fogger

Mister & fogger

Flow: 1.43 or 2.77 gph per outlet at 51 psi (up to 11.1 gph on the 4-outlet)
Pressure: 51–72.5 psi; seals at 20 psi
Connection: H anti-leak barb x conic female, or conic male x conic female
Sizes: Single, 2-outlet and 4-outlet; light blue 1.43 gph and dark blue 2.77 gph nozzles
Best for: Fine mist averaging 70 microns to drop greenhouse air temperature and raise humidity. Use with a Rivulis anti-leak H high-pressure mini valve to stop drainage at shut-off — fit it in the arrow direction. Recommended build is FLF plus anti-leak valve, microtube and stabilising weight. 100 micron / 150 mesh filtration

Fogger

Mister & fogger

Flow: Broad range of nozzle flow rates for different precipitation rates
Pressure: High-pressure Super LPD 60 psi; medium-pressure Super LPD opens 44 psi, closes 22 psi
Connection: PE and PVC connections; T or cross manifold assemblies
Best for: Cooling, humidifying and propagation. Extra-fine 55 micron droplets at 60 psi (69 micron on the medium-pressure LPD at 45 psi). Leakage prevention device gives simultaneous start-up and shut-down across the block. For cooling and humidifying run 4 foggers on a cross or 2 on a T — laterals 9.8–13.5 ft apart, heads 6–10 ft; add pesticide spraying and it is 2 on a T only, laterals 6–10 ft, heads 4–5 ft. 120 mesh filtration

Rondo Mist Sprayer

Mister & fogger

Flow: 12.4 gph (black) and 16.1 gph (blue) at 44 psi
Pressure: 36–58 psi
Connection: Ultra Conic inlet; assemblies with anti-leak valve, 12" tube, weight and coupling
Throw diameter: 6.5 ft average wetting diameter
Best for: Seed germination and cutting propagation — 150 micron droplets fall gently over the seed instead of the large drops a conventional spinner throws, in a uniform pattern averaging 6.5 ft. Use the standard anti-leak model below 51 psi and the H model above it. Add a 4x7 mm grommet to the mini valve for insertion into PVC laterals. 80 mesh filtration

Green Mist

Mister & fogger

Flow: 7.9–10.6 gph (7.9 at 29 psi, 9.0 at 36, 9.8 at 44, 10.6 at 50)
Pressure: 30–50 psi
Connection: Taper lock female with low-pressure Super LPD 4/7 (black)
Throw diameter: 4 ft
Best for: Misting and irrigation over propagation benches. Droplet size is tuned to stop mist drift, and distribution is symmetrical with no dead corners. Low-pressure LPD gives clean pulsed operation. Mount 3–4 ft above the bench, max 2.5 ft between heads on the lateral, 3 ft between laterals, and keep laterals within 10" of the bench edge. 100 mesh filtration

Accessory 3

Super LPD

Accessory

Pressure: Low-pressure opens 20 psi / closes 9 psi; medium-pressure opens 44 / closes 22; high-pressure opens 58 / closes 35
Connection: Barb 4/7, female, or 3/8" thread; bayonet x bayonet on the low-pressure model for Super Green Spin
Best for: Anti-drain valve, not an emitter — it stops drainage through the heads at shut-off and holds the system full and pressurised so the next cycle starts instantly. Minimal pressure loss even at high flow, one-stage open-or-shut action, easy-dismantle for cleaning. Three builds: black low-pressure for micro-sprinklers, green medium-pressure and blue high-pressure for foggers. Compatible with all Rivulis micro-sprinklers

Lateral Flush Valve

Accessory

Best for: Opens at the start of a cycle to flush the far end of the lateral, then closes once pressure builds — clears the sediment that otherwise settles there and blocks the last emitters on the run

Lateral LPD

Accessory

Best for: Holds the lateral charged between cycles so it does not drain down and refill each time — faster start-up and no puddling at the low points

Pressure reducing 3

V2000 (Pressure Reducing)

Pressure reducing

Pressure: To 145 psi (10 bar)
Sizes: 1.5"–8" straight; BSP/NPT or flange
Best for: Reduces pressure downstream of the valve to keep every block uniform. Available as a straight pressure reducing valve or as pressure reducing electric, so one valve both regulates and switches

V2500 (Pressure Reducing)

Pressure reducing

Pressure: To 145 psi (10 bar)
Sizes: 2"–6" — angle and straight
Best for: Piston-operated plastic pressure reducing valve for finer control of the regulation curve

V3000 (Pressure Reducing)

Pressure reducing

Pressure: To 145 psi (10 bar); over 6" rated to 232 psi (16 bar)
Sizes: 1"–16" — angle and straight
Best for: The metal pressure reducing valve for mainlines and pump sheds, in sizes and pressure ratings the plastics do not reach

Pressure sustaining 2

V3000 (Pressure Sustaining)

Pressure sustaining

Pressure: To 145 psi (10 bar); over 6" rated to 232 psi (16 bar)
Sizes: 1"–16" — angle and straight
Best for: Sustains minimum upstream pressure so priority zones and elevated blocks stay fed. Also available as a combined PR/PS valve that does both jobs in one body — which saves fitting two valves in series

V3500 (Pressure Sustaining)

Pressure sustaining

Sizes: 2"–10" — angle and straight
Best for: Piston valve range for maximum control. Also available manual, electric, pressure reducing and quick relief

AC solenoid valve 4

V1000

AC solenoid valve

Connection: BSP/NPT; 2-way internal or 3-way external control circuit; 3W solenoid 24 V AC
Sizes: 1" in-line, 1½" in-line, 2" in-line, 2" angle — blocks to 110 gpm (25 m³/h)
Best for: The economical choice for small farms, landscape and small commercial blocks. Every V1000 has a manual throttling knob for extra control over pressure and flow. Glass-filled nylon body, cover and diaphragm-piston assembly; full-bore seat with an unobstructed flow path for low head loss. The 2-way electric circuit is internal — no external tubes or accessories to fit or break. Also available manual, 9 V DC, hydraulic and pressure reducing

V2000 (Electric)

AC solenoid valve

Pressure: To 145 psi (10 bar)
Connection: 3W solenoid, 24 V AC normally closed; BSP/NPT, flange or ISO-16 in-line
Sizes: 1.5"–8" straight; BSP/NPT or flange
Best for: Rivulis’ main plastic agricultural valve, with a unique oval diaphragm design for minimum head loss. Also available manual, pressure reducing, pressure reducing electric and quick relief

V2500 (Electric)

AC solenoid valve

Pressure: To 145 psi (10 bar)
Sizes: 2"–6" — angle and straight; threaded, flanged, grooved, Victaulic or solvent weld
Best for: Piston-operated plastic valve where you want maximum control over the throttling curve rather than a diaphragm. Also available manual, pressure reducing and quick relief

V3000 (Electric)

AC solenoid valve

Pressure: To 145 psi (10 bar); metal valves over 6" rated to 232 psi (16 bar)
Sizes: 1"–16" — angle and straight
Best for: Patented springless diaphragm design in the valve chamber for reliable, precise operation. The size range and the 16 bar rating over 6" make this the pump-shed and mainline valve. Also available manual, pressure reducing, pressure sustaining, combined PR/PS and quick relief

DC latching solenoid valve 2

V1000 (9 V DC latching)

DC latching solenoid valve

Connection: 9 V DC latching solenoid; 2-way internal or 3-way external circuit; BSP/NPT
Sizes: 1" in-line, 1½" in-line, 2" in-line, 2" angle
Best for: The V1000 ordered with a 9 V DC latching solenoid for battery controllers on small farms and landscape jobs where running 24 V wire is not worth it. Keeps the manual throttling knob and the internal 2-way circuit

V2000 (9 V DC latching)

DC latching solenoid valve

Pressure: To 145 psi (10 bar)
Connection: 3W 9 V DC latching solenoid
Sizes: 2"L, 3", 3"L, 4", 6" — BSP/NPT or flange
Best for: The V2000 plastic body with a 9 V DC latching solenoid for battery-powered control. Oval diaphragm keeps head loss down

Air vent 3

Continuous / Automatic Air Release Valves

Air vent

Pressure: Opens from 0.10 bar (1.5 psi); maximum 145 psi (10 bar)
Sizes: 1/2", 3/4", 1"
Best for: Releases air during operation while the line is under pressure, reducing head loss and the flow loss that trapped air causes. Rivulis specify them on long constant-sloping segments, at peaks along the pipeline and relative to the hydraulic gradient, at line ends, before water meters, and on strainers and filters

Vacuum Breakers

Air vent

Pressure: Maximum 145 psi (10 bar)
Sizes: 3/4", 1", 2", 3"
Best for: Discharges air at start-up and lets air back in at shutdown so pipes and tubes cannot collapse. Rivulis specify one every 150–250 m on long continuous lines, on gentle peaks where vacuum is not a concern, and on pump filters needing air release

Combination Air Valves

Air vent

Pressure: Air and vacuum release from 0.20 bar (2.9 psi); maximum 145 psi (10 bar)
Sizes: 2"
Best for: Vacuum breaker and automatic air valve in one unit — air and vacuum release on start-up and shutdown, plus continuous release during operation. Rivulis specify them downstream of an isolating valve, on submains, on mains where the design calls for an air release/vacuum breaker, and on fertigation check valves

Spray stakes & emitters 5

ClickTif On-Line Dripper

Spray stakes & emitters

Flow: 1.3, 2.0, 3.0, 4.0, 8.0 and 12.0 l/h (0.34–3.2 gph)
Pressure: Minimum recommended working pressure 1 bar (14.5 psi)
Best for: Six flows from one body, with a labyrinth path that resists blocking. Maximum recommended 2.0 l/h per outlet on the 2-outlet build

E800 On-Line Dripper

Spray stakes & emitters

Flow: 2.0 l/h brown, 4.0 l/h black, 8.0 l/h green, 14.0 l/h red (0.53–3.7 gph)
Best for: Colour-coded turbulent-flow dripper across four flows, the widest single-outlet range in the Rivulis on-line family

E1000 On-Line Dripper

Spray stakes & emitters

Flow: 2 and 4 l/h (0.53 and 1.06 gph)
Best for: The multi-function port takes a barbed outlet, so one dripper can feed a single pot directly or run out to a distribution tube — no separate fitting

Katif PC

Spray stakes & emitters

Flow: 2.3 and 3.75 l/h (0.61 and 0.99 gph)
Pressure comp.: Yes
Sizes: Side outlet and top outlet versions
Best for: Compact PC dripper in side-outlet or top-outlet form, so the tube can leave the lateral whichever way the row runs

Supertif PC / PCND

Spray stakes & emitters

Pressure comp.: Yes — PCND version also no-drain
Connection: Barbed side outlet (SOL) with conic + barb options
Best for: PC dripper with a barbed side outlet — a Rivulis design that lets the microtube leave sideways rather than off the top, which keeps the assembly low in a tight canopy. The PCND build is also no-drain, so the lateral does not empty between cycles and the next start is instant

Filtration 10

F6150 Screen Filter

Filtration

Best for: The basic manual screen filter in the Rivulis range — the one that goes in front of a small block

F6400 Semi-Automatic Screen Filter

Filtration

Best for: Cleans on demand without opening the housing — a handle instead of a strip-down

F6260 Automatic Plastic Screen Filter

Filtration

Best for: Self-cleaning screen filter in a plastic body, for blocks that do not justify a metal automatic station

F3240 / F3240-IQ Automatic Screen Filter

Filtration

Best for: Hydraulically driven self-cleaning screen filter — no electrical supply needed at the filter station, which matters at a remote pump

F3340 / F3340 PRO Automatic Screen Filter

Filtration

Best for: Electrically driven automatic screen filter, with a PRO build for heavier duty

F3440 Continuous Circulation Screen Filter

Filtration

Best for: Filters continuously through the flush cycle, so downstream supply never drops — the point of a continuous-circulation design

F7050 Disc Filter

Filtration

Best for: Disc filtration gives depth rather than surface straining, so it holds organic matter that would blind a screen of the same rating

F7250 Automatic Disc Filter

Filtration

Best for: Self-cleaning disc filtration for dirty water where a screen would need constant attention

F2300 Media Filter

Filtration

Best for: Sand media filtration for surface water carrying algae and organic load

F1300 Hydrocyclone Filter

Filtration

Best for: Spins sand and grit out centrifugally before the main filter sees it — for well water, this is what stops you backflushing all day

Hose & fittings 1

PVC Molded Fittings

Hose & fittings

Best for: Rivulis moulded PVC fittings for connecting laterals and submains

Rivulis by category

Drip tape·Dripline·Oval hose·Layflat·Plastic impact sprinkler·Metal impact sprinkler·Fertilizer injector·Micro-sprinkler·Mister & fogger·Accessory·Pressure reducing·Pressure sustaining·AC solenoid valve·DC latching solenoid valve·Air vent·Spray stakes & emitters·Filtration·Hose & fittings